Get Better Golf

Unlock Your Golf Cart’s Potential: Adjusting or Removing the Governor

Golf carts have become increasingly popular in recent years as a mode of transportation on golf courses, neighborhoods, and resorts. However, the speed of a golf cart is usually limited to prevent accidents and other potential hazards.

This speed limitation is achieved through a device called a governor, which controls the maximum speed of the cart’s engine. In this article, we will discuss how to adjust or remove a golf cart governor, providing you with easy-to-follow steps to help you get the most out of your golf cart.

Removing Golf Cart Governor

Before we dive into the process of removing a golf cart governor, let’s first understand what it is and why you might want to remove it. The governor is a device that controls the speed of the engine by limiting the flow of fuel to the carburetor.

This can be frustrating for those who want to go faster, and so removing the governor is a popular modification. To remove the golf cart governor, you’ll need to access the engine compartment.

The first step is to remove the cable that connects the governor to the carburetor. Locate the cable, which is usually connected to the gas pedal, and remove it.

Next, locate the governor arm, which is attached to the threaded rod and tension spring. Disconnect the tension spring and the rod and remove them.

Once the threaded rod and tension spring are removed, the governor arm can be taken out. Disconnect the fuel volume cable from the governor arm and remove it.

Finally, disconnect any remaining cables or wiring connected to the governor and remove it from the engine compartment.

Adjusting Golf Cart Governor

If you want to go faster but don’t want to remove the governor entirely, you can adjust it to increase the cart’s speed. To do this, you need to alter the tension on the governor arm spring.

Start by locating the governor arm, which is usually found near the clutch pedal. The arm must be held in a fixed position either horizontally or vertically.

The next step is to loosen the governor arm’s tension spring. This can be done by using a wrench or pliers.

Once the spring is loose, adjust the tension by either making the spring tighter or looser. A tighter spring will cause the governor arm to restrict fuel flow sooner, whereas a looser spring will allow more fuel to flow through the carburetor.

Once you’ve made your desired changes, tighten the tension spring and check your work. Start the golf cart and test its speed to see if it has improved.

If you’re not happy with the speed, repeat the process until you achieve your desired results. Tools Needed for Adjusting or

Removing Golf Cart Governor

You may require different tools depending on which type of golf cart you have.

Generally, adjusting or removing a golf cart governor requires the following tools:

– Wrench

– Pliers

– Screwdriver

– Socket Set

Conclusion

We hope this article has helped you understand how to adjust or remove a golf cart governor. Remember, adjusting or removing a governor can be dangerous if not done correctly.

Always make sure you have the necessary tools, equipment, and experience to complete the task safely and effectively. If you’re unsure, it’s best to take your golf cart to a professional mechanic and let them handle it.

Follow these simple steps, and you’ll be able to unlock your golf cart’s full potential. Enjoy the ride!

The use of golf carts has become increasingly popular over the years as they offer an eco-friendly alternative for short-distance transportation.

However, for safety reasons, golf carts have governors to limit their maximum speed. If you want to remove or adjust the governor on your golf cart to achieve higher speeds, this article will guide you through the process step-by-step.

Process of

Removing Golf Cart Governor

Step 1: Remove the Cable

The governor is controlled by a thin cable that is connected to the carts carburetor. Start by locating the governor, usually near the engine.

You can identify the governor by the small cable that runs to it. Use a screwdriver to unscrew the cable mount and pull the cable free.

Step 2: Disconnect Cable from Governor

After removing the filter assembly from the carburetor tube, you can easily locate the governor mounted on the engine. Remove the governor’s mount by removing the bolt with a wrench.

Next, detach the thin cable running from the carburetor to the governor. Once removed, the governor will not be able to limit the fuel inflow, resulting in higher speeds.

Step 3: Disconnect Gas Pedal Connectors

Disconnect the connectors that link your gas pedal to the golf carts pedal. You can do this by locating and removing the plastic cover positioned at the pedal’s base.

You will need a screwdriver to remove the screws holding the cover in place. Once removed, disconnect the connectors that lock the gas pedal and golf cart pedal.

Step 4: Change Gas Pedal Route

Disconnect the carburetors governor lever and reroute the cable to the engine. This will increase the fuel inflow to the carburetor, allowing the engine to operate at a faster speed.

Step 5: Unscrew Bolt on Gas Pedal Shaft

Locate the bolt locked on the gas pedal shaft and remove it. This bolt prevents the pedal from accelerating past the governors preset speed limit.

Once removed, the pedal will be free to accelerate past the set maximum speed. Step 6: Test Golf Cart

Take the golf cart out to a flat area like a golf course and test it for speed.

If the golf cart achieves the desired speed, then the governor removal process is successful. Process of

Adjusting Golf Cart Governor

Step 1: Locate Governor Arm

To adjust the governor, start by locating the governor arm.

It is typically located on the rear axle housing and is covered by a protective plate. Remove the plate using a wrench or screwdriver to expose the governor arm.

Step 2: Find Governor Spring

Find the governor spring attached to the governor arm and the bracket next to it. At the other end of the spring, there will be a threaded rod that operates the governor.

Loosen the spring nut that secures it in place with a wrench. Step 3: Expose Engine

Remove the seat and its mounting screws to expose the golf carts engine.

Additionally, remove the plastic cover that protects the engine and its parts. This gives you easy access to the gas pedal cable and other governor components.

Step 4: Locate Gas Pedal Cable

Find the gas pedal cable running from the pedal to the governor. The cable is what connects the gas pedal to the governor arm and sets the rate at which fuel is pumped into the carburetor.

If you want to increase the speed, you will need to adjust the length of the governor spring. Step 5: Adjust Nuts on Threaded Rod

Adjust the nuts on the threaded rod that connects the governor to the carburetor.

Turning the nut counterclockwise increases the length of the spring, allowing the fuel to reach the carburetor more quickly, and enabling the engine to run at a faster speed. Step 6: Test Golf Cart

After adjusting the governors spring length, take your golf cart out for a test drive on a flat area like a golf course.

Observe your golf cart’s acceleration and speed. If the modifications improve the speed, then the adjustment process is successful.

Conclusion

Adjusting or removing the golf cart governor can significantly increase the speed of your golf cart, providing you with a thrilling driving experience. However, it is crucial to note that an improperly adjusted or removed governor can be hazardous and violate laws and regulations governing golf carts.

Therefore, ensure that you follow the steps outlined here for safe and effective results. Golf carts have become a popular mode of transportation, especially in golf courses, gated communities, and resorts.

However, the desire to increase the speed of the golf cart has led some owners to remove or adjust the governor. Before doing so, there are specific points that you must keep in mind to ensure that you do not damage the cart or violate any laws.

Warranty and Professional Assistance

Most golf carts come with a warranty that covers certain replacements and repairs. Modifying or removing the governor may interfere with the cart’s normal functioning and therefore puts the warranty at risk.

If your golf cart is still under warranty, it is essential to check the terms and conditions before attempting to modify or remove the governor. Further, tampering with electric golf carts may require professional assistance to avoid unnecessary damage.

If you are not confident in your ability to modify or replace parts, it is best to seek professional assistance.

Interference with Normal Functioning

When removing or adjusting the governor, it is crucial to use compatible replacement parts and abide by the manufacturer’s specifications. Installing incompatible parts can interfere with the golf cart’s normal operation and lead to significant problems.

Therefore, ensure that you use only high-quality parts and follow the manufacturer’s guidelines for modification or replacement. Apart from that, any changes you make to the cart must be done in adherence to the manufacturer’s specifications as printed in the manual.

Engaging in any activity outside the manufacturer’s instructions puts your golf cart at risk and could void your warranty. Therefore, before attempting to adjust or remove the governor, consult with the manufacturer’s manual.

Top Speed Limitations

One of the popular golf cart models is EZGO. These carts are limited to a top speed of 15 mph due to safety regulations.

If you want to increase the speed of an EZGO golf cart, you must go through the adjustment process. However, before doing so, you must ensure that the modifications do not exceed the legal limit.

In some states, golf carts are governed by state laws, which means that you cannot modify the speed of the cart past the established limit. If you violate these laws, you could be subject to a fine.

Therefore, research and ensure that the modifications you make are legal and within the established limits of your area.

Conclusion

In conclusion, adjusting or removing the governor on a golf cart can lead to increased speed and a thrilling driving experience. However, before adjusting or removing the governor, it is essential to keep in mind these key points.

First, check if your golf cart is still under warranty, as any modification can void it. Second, make sure that you use high-quality parts that meet the manufacturers specifications.

Lastly, ensure that the modifications are legal and within the established limits for your area. By keeping these points in mind, you can adjust or remove the golf cart governor safely and enjoyably.

Golf carts are a popular form of transportation but are limited to a certain speed by a governor. However, some owners desire speed and want to remove or adjust the governor.

It’s important to consider the risks before attempting any modifications, such as avoiding voiding the warranty, choosing compatible and high-quality replacement parts, and following the manufacturer’s specifications. Additionally, adhering to the legal speed limits for golf carts is essential.

Always conduct research before making any changes to your golf cart to avoid any legal repercussions. Remember, tinkering with the governor of a golf cart without proper knowledge may lead to dangerous circumstances.

FAQs:

– Can adjusting or removing the governor of a golf cart void my warranty? Yes, modifying or tampering with the governor can void the warranty on the golf cart.

– How do I know if replacement parts are compatible with my golf cart? Always double-check the manufacturer’s specifications and guidelines and use only high-quality parts.

– Are there legal speed limits for golf carts? Yes, some states have specific speed limits for golf carts.

Always check with your state’s laws and regulations before modifying the golf cart’s speed limit.

Popular Posts